The AQL (acceptance quality limit) is the worst process average, in percent defective, that you are willing to accept from a supplier over a series of lots. It decides how many pieces you pull and how many defectives you can find before you reject the lot. Choosing it is a risk decision, so it should be made once, written down, and applied the same way to every shipment.
1. Classify the defects first
An AQL applies to a class of defect, not to the part. ISO 2859-1 leaves the classes to you: class A for the highest concern with the smallest AQL, then class B and so on (3.1.5). ANSI/ASQ Z1.4 names three classes, and most receiving teams use them. Before choosing numbers, sort every characteristic on the drawing or specification into one:
| Class | What it means | Examples |
|---|---|---|
| Critical | Likely to cause hazardous or unsafe conditions for people using, maintaining or relying on the product, or to stop the end product performing its function. | Missing safety weld, wrong material on a pressure part, exposed live conductor. |
| Major | Not critical, but likely to cause a failure or materially reduce usability for its intended purpose. | Hole out of tolerance, wrong thread, cracked housing, missing component. |
| Minor | Unlikely to materially reduce usability; a departure from standard with little bearing on effective use. | Cosmetic scratch on a hidden face, slightly off-center label, light burr. |
Count defective pieces per class: a piece with two major defects is one major defective, and a piece with defects in two classes counts in the more serious one (ISO 2859-1, 3.1.7). Both standards also allow counting defects per 100 pieces instead.
2. Pick an AQL for each class
There is no universal AQL. These are typical starting points, not requirements; companies tighten them for safety-critical or regulated parts:
| Industry | Critical | Major | Minor |
|---|---|---|---|
| Consumer goods, general manufacturing | Not allowed (0) | 2.5 | 4.0 |
| Industrial and electronic components | Not allowed (0) | 1.0 or 0.65 | 2.5 |
| Medical devices | Not allowed (0) | 0.65 or tighter | 1.0 to 2.5 |
| Automotive (IATF 16949) | c = 0 | c = 0 | c = 0 |
| Aerospace (AS9138, or as the customer requires) | c = 0 or 100% | c = 0 | c = 0 |
Your customer's contract or quality manual overrides any table: if it specifies an AQL, use it.
A lower AQL is stricter. AQL 0.65 means you expect a process average of 0.65% defective or better; AQL 4.0 tolerates more. The AQL does not guarantee any single lot: a plan at AQL 2.5 still accepts a lot that is 5% defective a good part of the time. Check the limiting quality in the calculator to see how bad a lot can be and still slip through.
3. Choose the inspection level
The inspection level sets how big the sample is for a given lot size. General level II is used unless something else is specified, in both ISO 2859-1 and ANSI/ASQ Z1.4. Level I may be used when less discrimination is needed and level III when more is required. Special levels S-1 to S-4 give small samples, for use when small samples are necessary and larger sampling risks can be tolerated, such as destructive or very costly tests.
4. Decide whether you need zero acceptance (c = 0)
IATF 16949 (8.6.6) requires the acceptance level for attribute sampling to be zero defects, and AS9138 uses c = 0 plans for aerospace. A c = 0 plan accepts only when the sample has no defectives. Its sample size differs from the ISO 2859-1 or Z1.4 plan and is often smaller, chosen to give comparable protection against bad lots. The calculator's "Zero acceptance" option gives these plans.
5. Write it down
Put the defect classification, AQLs, inspection level and switching rules into your receiving inspection procedure, and record the plan used on every inspection. ISO 9001 (8.4.2) requires you to define how purchased product is verified, and to keep evidence that it was. AS9100 (8.5.1 c) 2)) adds that a sampling plan must be justified on recognized statistical principles, matched to the product's criticality and the process capability. Our procedure template has a section ready for it.